Early Rotary & 1979-85 Mazda RX-7 : Clutch/Pressure Plate

 : Clutch/Pressure Plate : Street - Stage 1 Clutch Disc 71-82 12A & 13B - 215mm

Street - Stage 1 Clutch Disc
71-82 12A & 13B - 215mm

Part Number: 12509

Price: $168.00

Qty:

Addtional Photos - Select to Enlarge

Facebook Share

Street - Stage 1 Clutch Disc
71-82 12A & 13B - 215mm

Street - Stage 1 Clutch Disc - 215mm OD
1971-82 12A & 13B Rotary Engine Applications
(except Rotary Pick-Up) 

This early rotary engine replacement clutch disc utilizes an organic compound disc lining, flattened marcel springs to reduce flexing, and two rivets per marcel plate to increase lining strength. The result is a disc that requires a bit more technique when starting, and releases quicker as compared with the stock disc. This disc is suited for both stock and high output street engines and can be used with either a stock pressure plate or a compatible aftermarket performance (Stage 1) version. Features a 22 tooth spline and 215mm OD.

Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.

Safety Note: None of the Racing Beat, Exedy, Mazda OE, or any aftermarket flywheel or clutch replacement components should ever be allowed to exceed 10,500 RPM under any condition. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM we highly recommend the installation of a transmission scatter shield or ballistic blanket. Failure to implement the above may result in serious injury or even death.

Actual disc not shown in photo.

 

Made in the USAMade in the USA under license by Racing Beat, Inc.
Prop65Warning

Customers who bought the above item also often bought:

Exedy Street Pressure Plate  - 79-82 RX-7 12A - 215mm Disc

Exedy Street Pressure Plate - 79-82 RX-7 12A - 215mm Disc

The Exedy Street Pressure Plate, intended for the 1979-82 RX-7 12A & 13B RX-7 chassis, is designed as a Mazda OE replacement for street applications. This RX-7re plate, and can be used with the 215mm OD stock disc or any equivalent replacement... Exedy Street Pressure Plate  - 79-82 RX-7 12A - 215mm Disc

Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

The original throwout bearing normally does not require replacement unless it has been abused in some way. However, if it has been making noise, such as a whirring sound when the clutch pedal is depressed, or if the slave linkage has run out of clearance,... Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

Transmission Seal Kit - 79-88 RX-7 Non-Turbo

Transmission Seal Kit - 79-88 RX-7 Non-Turbo

1979-88 RX-7 12A & 13B (Non-turbo) Transmission Seal Kit We recommend replacing the RX-7 transmission front seal and rear seals when re-installing the RX-7 transmission to reduce the risk of leakage. Although old age is a primary source of a failing... Transmission Seal Kit - 79-88 RX-7 Non-Turbo

RX-7 Flywheel - Aluminum - 74-82 12A Rotary

RX-7 Flywheel - Aluminum - 74-82 12A Rotary

Racing Beat-designed RX-7 flywheels are both engineered and manufactured by Racing Beat for a wide variety of rotary performance applications. This Racing Beat Aluminum Flywheel can be used on any early (pre-RX-7)  RX-2,... RX-7 Flywheel - Aluminum - 74-82 12A Rotary

Go to Racing Beat Home Page
Select: Go to Shopping Cart