Early Rotary & 1979-85 Mazda RX-7 : Clutch/Pressure Plate

 : Clutch/Pressure Plate : Sport/Race 4-Puck Clutch Disc 83-92 RX-7 12A & 13B Non-Turbo - 225mm OD

Sport/Race 4-Puck Clutch Disc
83-92 RX-7 12A & 13B Non-Turbo - 225mm OD

Part Number: 12529

Price: $206.00

Qty:

Addtional Photos - Select to Enlarge

Facebook Share

Sport/Race 4-Puck Clutch Disc
83-92 RX-7 12A & 13B Non-Turbo - 225mm OD

Sport/Race Stage 2 Clutch Disc
4-Puck Design - 225mm OD
1983-92 12A & 13B 6-Port

The Sport/Race 4-Puck Clutch Disc for the 1983-92 RX-7 chassis (12A & 13B 6-Port) is designed for road race and occasional drag race use. This 225mm OD disc features four (4) sintered copper pucks and a sprung hub for a very quick, positive engagement. The quick engagement/ disengagement requires careful driver attention - this disc is not recommended for street use. This disc interchanges exactly with the stock disc and can be used with the stock pressure plate.

Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.

Safety Note: None of the Racing Beat, Exedy, Mazda OE, or any aftermarket flywheel or clutch replacement components should ever be allowed to exceed 10,500 RPM under any condition. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM we highly recommend the installation of a transmission scatter shield or ballistic blanket. Failure to implement the above may result in serious injury or even death.

Actual disc not shown in photo.

Made in the USAMade in the USA under license by Racing Beat, Inc.
Prop65Warning

Customers who bought the above item also often bought:

Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

The original throwout bearing normally does not require replacement unless it has been abused in some way. However, if it has been making noise, such as a whirring sound when the clutch pedal is depressed, or if the slave linkage has run out of clearance,... Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

Exedy Street - Stage 1 Pressure Plate - 83-92 12A & 13B Non-Turbo - 225mm Disc

Exedy Street - Stage 1 Pressure Plate - 83-92 12A & 13B Non-Turbo - 225mm Disc

The Exedy Street/Strip Pressure Plate, intended for the 1983-92 RX-7 12A & 13B (6-Port Non-Turbo) chassis, is designed for high-performance street applications and for occasional drag or road racing. A stronger diaphragm spring applies substantially... Exedy Street - Stage 1 Pressure Plate - 83-92 12A & 13B Non-Turbo - 225mm Disc

Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm Disc

Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm Disc

The Exedy Race Pressure Plate (ZC505D)  for all 1983-1992 12A & 13B non-turbo rotary engines exerts very highre plate and is compatible with all 225mm OD RX-7 clutch discs. We strongly recommend replacing the throw-out bearing during any... Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm Disc

Transmission Throwout Bearing - 89-92 RX-7 - All

Transmission Throwout Bearing - 89-92 RX-7 - All

The original throwout bearing normally does not require replacement unless it has been abused in some way. However, if it has been making noise, such as a whirring sound when the clutch pedal is depressed, or if the slave linkage has run out of clearance,... Transmission Throwout Bearing - 89-92 RX-7 - All

Go to Racing Beat Home Page
Select: Go to Shopping Cart