Early Rotary & 1979-85 Mazda RX-7 : Oil System

 : Oil System : Oil Line Set RX-2, RX3 & RX-4

Oil Line Set
RX-2, RX3 & RX-4

Part Number: 11906

Price: $150.00

Qty:

Oil Line Set - RX-2, RX3 & RX-4 - Detail 1Oil Line Set - RX-2, RX3 & RX-4 - Detail 2Oil Line Set - RX-2, RX3 & RX-4 - Detail 3

Addtional Photos - Select to Enlarge

Facebook Share

Oil Line Set
RX-2, RX3 & RX-4

Racing Beat's fully assembled Stainless Steel Braided Hose Sets for the RX-2, RX-3, and RX-4 chassis replace the original factory oil cooler hoses. Significantly less costly than the Mazda replacement units, the Racing Beat-designed oil hose sets will easily meet the demands of street and most race applications.

Produced using Goodridge G-Line stainless steel braided hose, constructed using a seamless synthetic nitrile inner tube with an integral stainless steel braid and high tensile stainless steel outer cover. Precision-machined Goodridge aluminum alloy swivel-seal hose ends ensure a secure and superior seal. Each oil line set is carefully cut, assembled and tested by Racing Beat to ensure top-notch quality, reliability and performance.

Racing Beat's oil line sets are a direct replacement for the original factory lines - no cutting or refitting is required! Select from the adaptor fittings listed below to correctly install your oil hoses onto your chassis.

Required Adaptor Fittings:
1971-85 engines -
Part No. 11901 (3 required) Engine-to-hose adaptor (-10 to 16mm)
Part No. 11902 (1 required) Engine-to-hose adaptor (-10 to 18mm)

Assembled in the USA by Racing Beat, Inc.Assembled in the USA by Racing Beat, Inc.
Prop65Warning

Customers who bought the above item also often bought:

Oil Hose Adapter Fitting - 16MM to -10 Hose

Oil Hose Adapter Fitting - 16MM to -10 Hose

We offer the Racing Beat Oil Cooler Hose Adapter Fittings to simplify oil system plumbing. These fittings adapt the 16mm female metric threads in the 1971-95 rotary engine front cover and 1971-85 oil cooler (stock or factory race version) to accept -10... Oil Hose Adapter Fitting - 16MM to -10 Hose

Oil Hose Adapter Fitting - 18MM to -10 Hose

Oil Hose Adapter Fitting - 18MM to -10 Hose

We offer the Racing Beat Oil Cooler Hose Adapter Fittings to simplify oil system plumbing. These fittings adapt the 18mm female metric threads in the rotary engine rear housing to accept -10 hose ends. (All Racing Beat hose kits feature -10 fittings.)... Oil Hose Adapter Fitting - 18MM to -10 Hose

Road Race Header - Outlet Flange - Steel

Road Race Header - Outlet Flange - Steel

flange-gasket-guide.pdf This laser-cut flange can be used to fabricate a custom exhaust for use with the Racing Beat Road/Race Header. This two-hole flange measures 6" X 2-13/16" and features two 2" openings. This is the same... Road Race Header - Outlet Flange - Steel

Heater Water Outlet Plug - 81-earlier rotary engines

Heater Water Outlet Plug - 81-earlier rotary engines

This Heater-Water-Outlet Plug is an inexpensive and reliable way to plug the heater water outlet port on the rear rotor housing for those who do not use a heater. The 1981 and earlier rotary engines had a threaded fitting for the water outlet that... Heater Water Outlet Plug - 81-earlier rotary engines

Go to Racing Beat Home Page
Select: Go to Shopping Cart