Early Rotary & 1979-85 Mazda RX-7 : Oil System

 : Oil System : Oil Line Set 84-85 RX-7 GSL-SE

Oil Line Set
84-85 RX-7 GSL-SE

Part Number: 11908

Price: $155.00

Qty:

Oil Line Set - 84-85 RX-7 GSL-SE - Detail 1

Addtional Photos - Select to Enlarge

Facebook Share

Oil Line Set
84-85 RX-7 GSL-SE

Racing Beat's fully assembled Stainless Steel Braided Hose Sets for the 1984-1985 RX-7 GSL-SE chassis replace the original factory oil cooler hoses. Significantly less costly than the Mazda replacement units, the Racing Beat-designed RX-7 oil hose sets will easily meet the demands of street and most race applications.

Produced from Earl's Perform-O-Flex stainless steel braid-protected synthetic rubber hose and featuring an inner liner of synthetic rubber, including partial cover of stainless steel braid embedded into the liner during manufacturing. The hose liner is then bonded to a outer protective sheath of stainless steel wire braid. Precision-machined aluminum Swivel-Seal hose ends ensure a secure and superior seal. Each oil line set is carefully assembled and tested by Racing Beat to ensure top-notch quality, reliability and performance.

Racing Beat's RX-7 oil line sets are a direct replacement for the original factory lines - no cutting or refitting is required! Select from the adaptor fittings listed below to correctly install your oil hoses onto your chassis.

Required Adaptor Fittings:
1971-85 engines -
Part No. 11901 (3 required)
Part No. 11902 (1 required)

Assembled in the USA by Racing Beat, Inc.Assembled in the USA by Racing Beat, Inc.

Customers who bought the above item also often bought:

Oil Hose Adapter Fitting - 16MM to -10 Hose

Oil Hose Adapter Fitting - 16MM to -10 Hose

We offer the Racing Beat Oil Cooler Hose Adapter Fittings to simplify oil system plumbing. These fittings adapt the 16mm female metric threads in the front cover (1971-95 rotary engines) and oil cooler (1971-85 stock or factory race) to accept -10... Oil Hose Adapter Fitting - 16MM to -10 Hose

Oil Hose Adapter Fitting - 18MM to -10 Hose

Oil Hose Adapter Fitting - 18MM to -10 Hose

We offer the Racing Beat Oil Cooler Hose Adapter Fittings to simplify oil system plumbing. These fittings adapt the 18mm female metric threads in the rear housing to accept -10 hose ends. Additionally, these 18mm female fittings also fit the... Oil Hose Adapter Fitting - 18MM to -10 Hose

Mazda OEM Oil Filter - RX7, RX8, Protege, Miata

Mazda OEM Oil Filter - RX7, RX8, Protege, Miata

This OEM Mazda Oil Filter is intended for use on RX-7, RX-8, Protege & Protege 5, and Miata applications. It is recommended that the oil filter be replaced at the same time of an oil change. This is the genuine Mazda oil filter and is listed as... Mazda OEM Oil Filter - RX7, RX8, Protege, Miata

Aluminum Alternator Pulley -Double Sheave - 74-92 Rotary Engines (All)

Aluminum Alternator Pulley -Double Sheave - 74-92 Rotary Engines (All)

The Racing Beat-designed Double Sheave Aluminum Alternator Pulley reduces alternator RPM approximately 20% from stock RPM, and is intended for high performance and moderate race use. It is compatible with either the stock main pulley, or assuming... Aluminum Alternator Pulley -Double Sheave - 74-92 Rotary Engines (All)

Go to Racing Beat Home Page
Select: Go to Shopping Cart