1986-92 Mazda RX-7 Performance Parts : Clutch/Pressure Plate

 : Clutch/Pressure Plate : Sport/Race Disc -6 Puck 87-95 RX-7 Turbo & RX-8

Sport/Race Disc -6 Puck
87-95 RX-7 Turbo & RX-8

Part Number: 12523

Price: $178.00

Qty:

Addtional Photos - Select to Enlarge

Facebook Share

Sport/Race Disc -6 Puck
87-95 RX-7 Turbo & RX-8

The 6-Puck 240mm Sport/Race Clutch Disc for the 1987-95 RX-7 TURBO & RX-8 chassis is designed for road race and occasional drag race use. The disc features six (6) sintered copper pucks and a sprung hub for a quick, positive engagement. The quick engagement/disengagement requires careful driver attention - this disc is not recommended for street use. This disc interchanges exactly with the stock disc and can be used with the stock pressure plate.

As with all of our clutch products, it is built only from new parts.

Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.

WARNING: None of the Flywheel or Clutch components shown in this catalog should ever be allowed to exceed 10,500 RPM under any condition. This same RPM limit applies to stock components. You must use an engine RPM-limiter to prevent excessive RPM. If your RX-7 engine is capable of exceeding 8,500 RPM (or 9,000 RPM for the RX-8 Renesis engine) you must install a transmission scatter shield, or ballistic blanket. Failure to implement the above may result in serious injury or even death.

Customers who bought the above item also often bought:

Oil Hose Adapter Fitting - 16MM to -10 Hose

Oil Hose Adapter Fitting - 16MM to -10 Hose

We offer the Racing Beat Oil Cooler Hose Adapter Fittings to simplify oil system plumbing. These fittings adapt the 16mm female metric threads in the front cover (1971-95 rotary engines) and oil cooler (1971-85 stock or factory race) to accept -10 hose... Oil Hose Adapter Fitting - 16MM to -10 Hose

Aluminum Alternator Pulley -Double Sheave - 74-92 Rotary Engines (All)

Aluminum Alternator Pulley -Double Sheave - 74-92 Rotary Engines (All)

The Racing Beat-designed Double Sheave Aluminum Alternator Pulley reduces alternator RPM approximately 20% from stock RPM, and is intended for high performance and moderate race use. It is compatible with either the stock main pulley, or assuming you... Aluminum Alternator Pulley -Double Sheave - 74-92 Rotary Engines (All)

Rotor Oil Filler Cap

Rotor Oil Filler Cap

The Racing Beat-designed and manufactured Rotor Oil Filler Cap fits All Mazda 12A and 13B Rotary Engines Except: 1993-95 RX-7, 2004-08 Auto-trans RX-8, 2009 RX-8 ALL) Yes, we know that there are many "rotor shaped" oil caps available on... Rotor Oil Filler Cap

Carbon Race Apex Seal - 86-92 Non-Turbo

Carbon Race Apex Seal - 86-92 Non-Turbo

Racing Beat's 1986-92 13B Non-Turbo (2mm) Carbon Race Apex Seals are specifically designed to replace the stock cast iron apex seals in rotary engines operating near, or above, 8,500 RPM. These aluminum-filled carbon apex seals are a one-piece... Carbon Race Apex Seal - 86-92 Non-Turbo

Go to Racing Beat Home Page
Select: Go to Shopping Cart