1986-92 Mazda RX-7 Performance Parts : Clutch/Pressure Plate

 : Clutch/Pressure Plate : Race Disc - 6 Puck 83-92 RX-7 Non-Turbo

Race Disc - 6 Puck
83-92 RX-7 Non-Turbo

Part Number: 12526

Price: $142.00

Qty:

Addtional Photos - Select to Enlarge

Facebook Share

Race Disc - 6 Puck
83-92 RX-7 Non-Turbo

The 225mm Race Clutch Disc, for the 1983-92 RX-7 Non-Turbo, is designed for drag and road race use. The disc incorporates six (6) sintered copper pucks and a solid hub for quick, positive engagement, greater fatigue resistance and improved heat dissipation. The sharpened engagement/disengagement characteristics of this disc require careful driver attention - this disc is not intended for street use.
As with all of our clutch products, it is built only from new parts.

Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage. (See bottom of parts list).

WARNING: None of the Flywheel or Clutch components shown in this catalog should ever be allowed to exceed 10,500 RPM under any condition. This same RPM limit applies to stock components. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield, or ballistic blanket. Failure to implement the above may result in serious injury or even death.

Customers who bought the above item also often bought:

Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm

Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm

The Exedy Race Pressure Plate for all 1983-1992 12A & 13B non-turbo rotary engines exerts very highre plate. This pressure plate is compatible with all 225mm RX-7 clutch discs.

We strongly recommend replacing the throw-out bearing... Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm

Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

The original throwout bearing normally does not require replacement unless it has been abused in some way. However, if it has been making noise, such as a whirring sound when the clutch pedal is depressed, or if the slave linkage has run out of... Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

Oil Line Set - 86-92 RX-7 All

Oil Line Set - 86-92 RX-7 All

Racing Beat's fully assembled Stainless Steel Oil Cooler Hose Sets for the 1986-1992 RX-7 TURBO II and Non-Turbo chassis replace the original factory RX-7 oil cooler hoses. Significantly less costly than the Mazda replacement RX-7 oil lines, the... Oil Line Set - 86-92 RX-7 All

Down Pipe & Presilencer Gasket - 86-92 RX-7

Down Pipe & Presilencer Gasket - 86-92 RX-7

flange-gasket-guide.pdf

This gasket can be used with the following Racing Beat exhaust components:

Non-turbo Down-Pipe
1986-92 RX-7 (Front & Rear) - This gasket can be used at the... Down Pipe & Presilencer Gasket - 86-92 RX-7

Go to Racing Beat Home Page
Select: Go to Shopping Cart