1993-95 Mazda RX-7 Performance Parts : Oil System

 : Oil System : Oil Pressure Regulator - Race 105-115 PSI

Oil Pressure Regulator - Race 105-115 PSI

Part Number: 11812

Price: $115.00

Qty:

Oil Pressure Regulator - Race 105-115 PSI -  - Detail 1

Addtional Photos - Select to Enlarge

Facebook Share

Oil Pressure Regulator - Race 105-115 PSI

The Racing Beat High Performance Rear Oil Pressure Regulator interchanges exactly with the stock rear oil pressure regulator on all 1971-2008 12A, 13B, and 20B engines. This oil pressure regulator is designed to bypass at 105-115 PSI. (Pressure this high should be used only for racing). When using this regulator, the front pressure regulator should be shimmed an 1/8-inch to ensure that it does not limit the oil pressure (shims included).

As a general rule, oil pressure should be increased as the horsepower output and engine RPM increases. As horsepower and RPM demands increase, it is beneficial to have higher oil pressure between the shafts and bearings to prevent possible catastrophic contact between spinning components. Additionally, as oil pressure is increased, flow rate also increases - hence, more oil is available to cool the bearings and rotors.

Tech Notes:

 - The 1993-95 13B Twin Turbo the factory rear oil pressure regulator bypasses at a maximum nominal rate of 110 PSI. For more information on how to increase oil pressure for this application visit our Oil Tech Tips section.

-The 2004-2008 RX-8 Renesis engine factory rear oil pressure regulator bypasses at a maximum nominal rate of 80 PSI. For this application we offer our Street Regulator - 90 PSI.

- The 2009-2011 RX-8 Renesis engine is not equipped with a rear pressure regulator. Nominal oil maximum oil pressure on this application is 110-115 PSI. We do ot offer a regulator to increase the oil pressure on this application.

Made in the USAMade in the USA by Racing Beat, Inc.

Customers who bought the above item also often bought:

Race Oil Pump - 74-85 12A & 13B

Race Oil Pump - 74-85 12A & 13B

The Mazda Competition Department Oil Pump, for all 1974-85 12A and 13B engines, interchanges exactly with the stock oil pump in all 1974-85 engines. The race oil pump rotor set width is 17.5mm, as opposed to 15mm in stock 1974-75 engines and 12.5mm... Race Oil Pump - 74-85 12A & 13B

Aluminum Main Pulley - Double Sheave - 74-92 Rotary Engines (All)

Aluminum Main Pulley - Double Sheave - 74-92 Rotary Engines (All)

The Racing Beat Aluminum Double Sheave Main Drive Pulley for virtually all 1974-92 12A and 13B engines is designed for high performance/RPM street and moderate racing use, slowing the water pump and alternator 13-15 %, thereby reducing cavitation... Aluminum Main Pulley - Double Sheave - 74-92 Rotary Engines (All)

Intake Gasket - Engine-to-Manifold - 76-78 13B

Intake Gasket - Engine-to-Manifold - 76-78 13B

The 1976-78 13B Engine-to-Manifold Mazda Factory gasket is intended to fit securely between the intake manifold and the engine.

If you are installing a Racing Beat Holley or Dellorto intake manifold, two (2) Water... Intake Gasket - Engine-to-Manifold - 76-78 13B

Devcon Plastic Putty - Steel

Devcon Plastic Putty - Steel

When building a peripheral port engine it is necessary to fill the intake ports on the cast iron side housings with a material that will form a tough, durable metallic mass - Devcon Plastic Steel Putty (10110) is the material of choice. Easy to use... Devcon Plastic Putty - Steel

Go to Racing Beat Home Page
Select: Go to Shopping Cart