Early Rotary & 1979-85 Mazda RX-7 : Brake Discs

 : Brake - Discs : Stop Tech Brake Rotors Slotted - Front 79-83 RX-7 12A - All

Stop Tech Brake Rotors Slotted - Front
79-83 RX-7 12A - All

Part Number: 14535

Price: $340.00

Qty:

Addtional Photos - Select to Enlarge

Stop Tech Brake Rotors Slotted - Front
79-83 RX-7 12A - All

*Discontinued by StopTech as of 7/2023. Once listing is gone, we will no longer carry.)

StopTech Sport Brake Slotted Rotors - 1979-83 RX-7
(Priced and sold as left/right front sets)

Installation Note: The front brake rotors for the 1979-83 RX-7 contain both an inner and outer bearing. The use of these rotors requires that you obtain the inner bearing & seal, and outer bearing, prior to installation. You can source these bearings through a local auto parts store, or for your convenience you can order our Centric Complete Bearing Kit.

Heat is the primary cause of ineffective or reduced braking performance due to fade. There is actually a boundary layer of gases that builds up between the pad and rotor surface, which inhibits performance. Here's where StopTech rotors make a big difference. The exclusive Vac-U-Slots machined into the rotor wipes brake pads clean, evacuates gases, and sheds heat. A combination of a high performance pad and StopTech RX-7 brake rotors will provide superior reliable braking for your RX-7, with an upgrade to larger diameter rotors and bigger calipers typically only needed for the most severe competition applications.

StopTech RX-7 brake rotors are manufactured to the highest tolerances keeping safety and quality their number one priority. Slotting, unlike drilling, doesn't compromise the structural integrity of the rotor. When you drill a rotor you weaken it and cause stress points that can lead to cracking and ultimately failure. Also, drilled rotors lose considerable surface area compared to slotted rotors, which means less active braking area for pad to rotor contact.

StopTech's RX-7 brake rotors are made using the highest quality Original Equipment replacement blanks. Competitors will sacrifice quality by using inexpensive off-shore castings. Typically these are made of inferior porous material and often have less cooling fins than their OE counterpart. These fins also serve to reinforce the rotor and guard against warpage. StopTech rotors always meet and/or exceed all OE specifications. It's also important to know that the exclusive Vac-U-Slot is tapered to enhance evacuation of heat and gases. All machining is done in house to StopTech's application specific tolerances to ensure optimum quality control.

StopTech RX-7 Sport Rotors are finished with black e-coating on both sides of the hat, inside the cooling vanes, and on the outside edge. E-coating is a superior electro-statically applied finish designed to withstand 400 hours of salt water exposure without rusting. This is especially important on both mounting faces of the hat where it touches the hub flange and back face of the wheel. Any accumulation of rust in these area can lead to installed lateral run out issues.

Racing Beat Application Notes:
For maximum braking performance we strongly recommend the use of a set of upgraded brake pads with this use of these rotors. Although OE or standard replacement  pads can be used, noticeable braking improvement will be immediately noticed after the installation of a performance pad set.

Actual rotor NOT shown in photo.

Prop65Warning

Racing Beat Recommended Accessories:

Centric Brake Rotor Bearing Kit - Front - 79-83 RX-7 12A

Centric Brake Rotor Bearing Kit - Front - 79-83 RX-7 12A

Centric Brake Rotor Bearing and Seal Kit - 1979-83 RX-7 Front When replacing or servicing the rotors on you RX-7 you'll either need to install or replace the roller bearings. Racing Beat combines all required bearings and oil seals for two rotors...
Price: $63.00 MORE INFO »

Go to Racing Beat Home Page
Select: Go to Shopping Cart