1986-92 Mazda RX-7 Performance Parts : Clutch/Pressure Plate

: Clutch/Pressure Plate : Race 4-Puck Clutch Disc 83-92 RX-7 Non-Turbo - 225mm OD

Race 4-Puck Clutch Disc
83-92 RX-7 Non-Turbo - 225mm OD

Part Number: 12522

Price: $168.00

Qty:

Addtional Photos - Select to Enlarge

Facebook Share

Race 4-Puck Clutch Disc
83-92 RX-7 Non-Turbo - 225mm OD

Race Stage 3 Clutch Disc
Solid Hub / 4-Puck Design - 225mm OD
1983-92 RX-7 12A & 13B (non-turbo) Applications

The Race 4-Puck 225mm OD Clutch Disc, offered for all 1983-92 RX-7 Non-Turbo chassis, is designed for drag and road race use. The disc incorporates four (4) sintered copper pucks and a solid hub for quick, positive engagement, greater fatigue resistance and improved heat dissipation. The sharpened engagement/disengagement characteristics of this disc require careful driver attention - this disc is not intended for street use.

Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.

Safety Note: None of the Racing Beat, Exedy, Mazda OE, or any aftermarket flywheel or clutch replacement components should ever be allowed to exceed 10,500 RPM under any condition. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM we highly recommend the installation of a transmission scatter shield or ballistic blanket. Failure to implement the above may result in serious injury or even death.

Actual disc not shown in photo.

Made in the USAMade in the USA under license by Racing Beat, Inc.
Prop65Warning

Customers who bought the above item also often bought:

Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm Disc

Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm Disc

The Exedy Race Pressure Plate (ZC505D)  for all 1983-1992 12A & 13B non-turbo rotary engines exerts very highre plate and is compatible with all 225mm OD RX-7 clutch discs. We strongly recommend replacing the throw-out bearing during any... Exedy Race Pressure Plate - 1983-92 12A & 13B Non-Turbo - 225mm Disc

Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

The original throwout bearing normally does not require replacement unless it has been abused in some way. However, if it has been making noise, such as a whirring sound when the clutch pedal is depressed, or if the slave linkage has run out of clearance,... Transmission Throwout Bearing - 79-88 - 12A & 13B 6 Port

RX-7 Flywheel - Aluminum - 83-92 RX-7 Non-Turbo

RX-7 Flywheel - Aluminum - 83-92 RX-7 Non-Turbo

Racing Beat-designed RX-7 flywheels are both engineered and manufactured by Racing Beat for a wide variety of rotary performance applications. This Racing Beat Aluminum Flywheel can be used on all 1983-85 RX-7 12A engines and on all... RX-7 Flywheel - Aluminum - 83-92 RX-7 Non-Turbo

Exedy Street - Stage 1 Pressure Plate - 83-92 12A & 13B Non-Turbo - 225mm Disc

Exedy Street - Stage 1 Pressure Plate - 83-92 12A & 13B Non-Turbo - 225mm Disc

The Exedy Street/Strip Pressure Plate, intended for the 1983-92 RX-7 12A & 13B (6-Port Non-Turbo) chassis, is designed for high-performance street applications and for occasional drag or road racing. A stronger diaphragm spring applies substantially... Exedy Street - Stage 1 Pressure Plate - 83-92 12A & 13B Non-Turbo - 225mm Disc

Go to Racing Beat Home Page
Select: Go to Shopping Cart